Semi-reciprocal polarization maintaining fibre coupler with distinctive transmission characteristics | Scientific Reports

Scientific Reports volume 5, Article number: 17268 (2015) Cite this article

1260 Accesses

6 Citations

Metrics details

Optical couplers are very important devices in optical communication systems and optical sensor systems. Several types of optical couplers with different materials or different transmission characteristics have been reported. Here we propose a semi-reciprocal polarization maintaining fibre coupler with unique transmission characteristics, which is distinct from conventional polarization maintaining fibre couplers and polarization beam splitters and investigate the characteristics of the coupler theoretically and experimentally. The experimental results show that for circularly and elliptically polarized input light, the proposed coupler will act both as an in-line polariser and a conventional polarization maintaining fibre coupler. The output polarization extinction ratio of the transmission arm is 31.79 dB at a centre wavelength of 841 nm. For linearly polarized input light, the coupler will merely act as a conventional 3 dB polarization maintaining fibre coupler. The unique features of the proposed coupler enables the removal of polarisers from optical sensor systems and coherent optical communication systems and reduces the insertion loss and production cost of the optical path. Therefore there is wide application for this device in optical sensor systems and optical communication systems.

Optical couplers are ubiquitous in optical communication systems, including wavelength division multiplexing systems, coherent optical communication systems and optical networks1,2. Optical couplers are also important elements of optical sensor systems, such as optical gyroscopes, optical hydrophones and optical current sensors, etc.3,4,5,6. To date, several types of optical couplers with different materials or different transmission characteristics7,8,9, such as waveguide couplers10, fused-taper single mode fibre couplers11, fused-taper polarization maintaining fibre (PMF) couplers and photonic crystal fibre couplers have been reported12,13,14,15,16,17,18.

In this article, we propose a semi-reciprocal PMF coupler with unique transmission characteristics, which is distinct from both typical PMF couplers and polarization beam splitters (PBS) and analyse the transmission characteristics theoretically and experimentally. Conventional PMF couplers are reciprocal devices, which can combine or split the input lights and maintain their polarization states at the output ports19. The splitting ratio of the coupler is almost a constant when the input polarization states are changed, as shown in Fig. 1a. Other fused-taper fibre devices are PBSs. PBSs can split a circularly or elliptically polarized beam into two orthogonal linearly polarized beams, as shown in Fig. 1b, but cannot split a linearly polarized beam into two beams20.

Transmission characteristics.

(a) Transmission characteristics of a conventional PMF coupler. (b) Transmission characteristics of a PBS. (c) Transmission characteristics of a semi-reciprocal PMF coupler when linearly polarised light is input. (d) Transmission characteristics of the semi-reciprocal PMF coupler when elliptically and circularly polarised light is input. Pink and blue arrows represent the light intensities of the x and y polarized light, respectively.

Figure 1c,d show the transmission characteristics of the semi-reciprocal PMF coupler. When linearly polarized light is input, as shown in Fig. 1c, the proposed coupler will act as a typical PMF coupler. When elliptically or circularly polarized light is input, as shown in Fig. 1d, the transmission arm (port 1 ↔ port 3 and port 2 ↔ port 4) of the coupler will act as an in-line polariser, translating the elliptically or circularly polarized light into linearly polarized light with high polarization extinction ratio (PER) and the coupling arm (port 1 ↔ port 4 and port 2 ↔ port 3) will merely act as a typical PMF coupler. The unique features of the proposed PMF coupler enables the removal of the PMF polariser from optical sensor systems and coherent optical communication systems and reduces the insertion loss and production cost of the optical path21. Therefore, this semi-reciprocal PMF coupler has wide application in optical sensor systems and optical communication systems.

Figure 2 shows a cross-sectional schematic diagram of the semi-reciprocal PMF coupler, where a is the radius of the fibre core, d is the distance between the centres of two cores at the fused-elongated section and n1 and n2 are the core and cladding refractive index of the fibre, respectively.

The cross-sectional schematic diagram of the semi-reciprocal PMF coupler.

In the approximation of weak coupling, the output intensity P3 at port 3 and the output intensity P4 at port 4 are given by:

Where P0 is the power launched in port 1, κ is the coupling coefficient and L is the coupling length. According to coupled-mode theory for optical fibres, the coupling coefficient of two identical and parallel step-index optical fibres can be expressed as:

Where , K0 and K1 are the modified Bessel functions of the second kind and of order 0 and 1, respectively. V is the normalized frequency of the core of an optical fibre, which is defined as:

Where λ is the signal wavelength and the parameters U and V satisfy:

J0 and J1 are the 0-order and 1-order Bessel functions, respectively. Eq. (3) indicates that the coupling coefficient κ depends on the normalized frequency V and the normalized distance between the centres of two cores d/a.

The normalized frequency V should take a value that guarantees the single mode condition. For an optical fibre having a step type refractive index distribution, the single mode condition is guaranteed when V<=2.405 is satisfied. Eq. (4) indicates that the normalized frequency V depends on the parameters of the optical fibre. For polarization maintaining fibre, because of the mode birefringent index nb = | n1x– n1y|, the normalized frequency Vx of x polarized light is different from the normalized frequency Vy of y polarized light. The coupling characteristics of x polarized light and y polarized light are not the same and the coupling coefficient κ depends on the polarization of the light. The parameters of the PMF we used were as follows (http://www.fujikura.co.jp): wavelength λ = 850 nm, core radius a = 1.7 μm, core index n1 = 1.460, relative refractive-index difference between core and claddings (n1−n2)/n1 = 0.35%, mode birefringent index at used wavelength nb = | n1x– n1y| = 5 × 10−4. Therefore, for the PM fibre we used, the values of normalized frequency were Vx = 1.5337 and Vy = 1.4566, respectively.

In Fig. 3a, the coupling coefficients κx and κy are plotted for x polarized light and y polarized light, respectively. When the centres of two cores are close to each other (normalized distance d/a is approximately 3 in Fig. 3a), κx ≈ κy, so that the coupling characteristics of the x polarized light are almost the same as for y polarized light. The coupling coefficient κ depends slightly on the polarization of the light. This is the case for the conventional PMF coupler, which combines or splits the input lights and maintains their polarization states at the output ports. The splitting ratio of ports 3 and 4 is almost a constant when the input polarization states are changed.

Examples of simulation results.

(a) Coupling coefficients κx and κy of x polarized light and y polarized light as a function of the normalized distance between the centres of two cores d/a. The red line represents the coupling coefficient κx decreasing exponentially for Vx = 1.5337 and the blue line represents the coupling coefficient κy decreasing exponentially for Vy = 1.4566. The coupling coefficient κ is changed by varying the normalized distance d/a between the centres of two cores. (b) Normalized light intensities of x polarized light and y polarized light at port 3 of the coupler as a function of the normalized distance d/a. The red and blue lines represent the normalized light intensities of the x polarized light and y polarized light, respectively.

When the distance between the centres of two cores is greater than a threshold, the difference between the coupling coefficients κx and κy becomes obvious. The coupling coefficient κ depends on the polarization of the light, therefore the coupling characteristic of x polarized light is totally different from y polarized light. For polarization maintaining optical fibres, Eq. (1) is satisfied for both the x polarized light and y polarized light. When the value of the coupling coefficient for x polarized light κx and y polarized light κy satisfies:

the output intensities of x polarized light and y polarized light at port 3 can be expressed as:

which is the case for the proposed semi-reciprocal PMF coupler.

Figure 3b shows the normalized light intensities of x polarized light and y polarized light at port 3 of the coupler calculated as a function of d/a by assuming that the coupling length L of the coupler is 10 mm in Eq. (9). When the normalized distance d/a between the centres of the two cores is approximately 5 as shown in Fig. 3b, almost all y polarized light passes through port 4, while little light output is measured at port 3. Conversely, the measured light intensity of x polarized light at port 3 is almost the same as at port 4. This demonstrates the special transmission characteristic of the semi-reciprocal PMF coupler. Therefore the normalized distance d/a between the centres of two cores can be designed to be 5, as shown in Fig. 3b.

The analysis therefore predicts that if x polarized light is applied to port 1, the coupler will act as a conventional 3 dB fused-taper PMF coupler. Conversely, if we apply circularly/elliptically polarized light to port 1, port 3 will output linearly polarized light with a high PER = 10log(Px/Py) and port 4 will output elliptically polarized light. This means that for circularly/elliptically polarized input light, the transmission arm will act as an in-line PMF polariser translating the circularly/elliptically polarized light into linearly polarized light with a high PER and the coupling arm will act as a typical PMF coupler. The above discussion uses coupled-mode optical fibre theory to investigate the expected transmission characteristics of the proposed coupler. We now present the results of experimentation.

Figure 4a shows the experimental setup used to evaluate the proposed PMF coupler. Light from a broadband super luminescent light emitting diode (SLED, EXALOS-EXS210027-02, 3-dB centre wavelength 835.9 nm, 3-dB bandwidth 50.8 nm, 10-dB centre wavelength 838.1 nm, 10-dB bandwidth 76.3 nm, http://www.exalos.com) is polarized by a fibre optical polariser as shown in Fig. 4a. The linearly polarized light with PER of over 35 dB is launched into port 1 of the coupler. θ is the angle between the light’s polarization direction and the slow axis of port 1. Therefore, there are two orthogonally polarized light arrangements which can be applied: in one, x polarized light is input, corresponding to an input polarization angle of θ = 0° and in the second, y polarized light is input, corresponding to input polarization angle of θ = 90°. The input light intensity at port 1 and the output light intensities at port 3, are measured using optical spectrum analysers (YOKGAWA AQ6370C) as shown in Fig. 4b. The wavelength range is from 800 nm to 900 nm. The output light intensity values of x polarized light and y polarized light are measured as a function of wavelength in steps of 0.2 nm.

Experimental setup used to evaluate the semi-reciprocal PMF coupler.

(a) Experimental setup. (b) The input light intensity at port 1 and the output light intensities at port 3 measured as a function of wavelength. The green line represents input light intensity at port 1, red and blue lines represent the output light intensities of x polarized light and y polarized light at port 3, respectively.

Figure 5a shows the relationship between the wavelength and the coupling ratio of the semi-reciprocal PMF coupler. The coupling ratio of the proposed coupler of x polarized light and y polarized light are plotted as a function of wavelength in steps of 0.2 nm. The coupling ratio of the 2 × 2 coupler is defined as P3/(P3 + P4), where P3 and P4 are the output light intensities at port 3 and port 4, respectively. Therefore, the coupling ratios of x polarized light and y polarized light are defined as P3i/(P3i + P4i), (i = x, y), where P3x and P4x are the output light intensities at port 3 and port 4 when input light is x polarized and P3y and P4y are the output light intensities at port 3 and port 4 when input light is y polarized.

Experimental results of coupling ratio and output PER.

(a) Output light intensities of x polarized light and y polarized light as a function of wavelength in steps of 0.2 nm. The red and blue lines represent the normalized light intensities of the x polarized light and y polarized light, respectively. (b) Relationship between the wavelength and the output PER of port 3 when applying circularly polarized light to port 1. The red line represents the output PER of sample 1 and the blue line represents the output PER of sample 2.

When x polarized light (corresponding to an input polarization angle of θ = 0°) is applied to port 1 of the proposed coupler, the output light intensity of x polarized light at port 3 is almost the same as at port 4 at a wavelength of 843 nm, as shown in Fig. 5a. Therefore, the coupling ratio of x polarized light is P3x/(P3x + P4x) = 52% at a centre wavelength of 843 nm. Conversely, when y polarized light (corresponding to an input polarization angle of θ = 90°) is applied to port 1, almost all the light intensity passes through port 4, while little output light intensity is measured at port 3 at wavelength 843 nm. Thus the coupling ratio of y polarized light is P3y/(P3y+P4y) = 0.042% at a centre wavelength of 843 nm, as shown in Fig. 5a.

Figure 5b shows the experimental results of output PER at port 3 if circularly polarized light is applied to port 1, measured as a function of wavelength. The wavelength range is from 800 nm to 900 nm and the PER value is plotted in steps of 0.2 nm. The experimental results show that the maximum output PER at port 3 of sample 1 is 31.79 dB with a centre wavelength of 841.2 nm and the maximum output PER at port 3 of sample 2 is 29.86 dB with a centre wavelength of 840.8 nm as designed. A PER of over 25 dB is obtained in a wavelength region of over 10 nm at approximately 840 nm and a PER of over 20 dB is obtained in a wavelength region of 25 nm.

The experimental results prove that for x polarized input light, the proposed coupler has the function of splitting the input polarized light with a splitting ratio of port 3 to port 4 equal to about 52%:48%. On the other hand, for circularly and elliptically polarized light, the transmission arm (port 1 ↔ port 3 and port 2 ↔ port 4) of the proposed coupler has the function of converting the input light into linearly polarized light with a PER of 30 dB, while the coupling arm (port 1 ↔ port 4 and port 2 ↔ port 3) merely has a light splitting function.

In summary, we propose and demonstrate a semi-reciprocal PMF coupler with distinctive transmission characteristics and investigate the coupler theoretically and experimentally. Experimental results show that for circularly and elliptically polarized input light, the semi-reciprocal coupler will act as an in-line PMF polariser and as a conventional PMF coupler and the output PER of the transmission arm is over 30 dB with a centre wavelength of about 841 nm. For linearly polarized input light, the coupler will merely act as a conventional 3 dB PMF coupler with splitting ratio equal to about 52%:48%. The unique features of the proposed coupler enable us to remove the PMF polariser from optical fibre gyroscopes, optical fibre hydrophones and coherent optical communication systems, etc. Therefore, this semi-reciprocal PMF coupler has wide application in optical sensor systems and optical communication systems.

The proposed semi-reciprocal coupler has two PANDA fibres arranged side by side in such a way that their axes of polarization are parallel to each other as shown in Fig. 2. The fibres are heated and elongated in the longitudinal direction, thus forming a fused-taper section. The degree of separation of the two cores at the fused-taper section was adjusted to ensure the normalized distance d/a between the centres of the two cores was 5 by design. In the production of the fused-taper section, the temperature of the heating source was set lower than the temperature of a conventional PMF coupler, the distance from the heating source increased and the elongation operation was performed quickly so as to reduce the amount of heat per unit time. Elongation was terminated when the coupling length L was 10 mm as desired, ensuring that the coupling ratio of x polarized light was about 50% and the coupling ratio of y polarized light was less than 0.05% with a centre wavelength of 840 nm.

How to cite this article: Wang, X. et al. Semi-reciprocal polarization maintaining fibre coupler with distinctive transmission characteristics. Sci. Rep. 5, 17268; doi: 10.1038/srep17268 (2015).

Crespi, A. et al. Integrated photonic quantum gates for polarization qubits, Nature Communication. Volume: 2, 566 (2011).

Article ADS Google Scholar

Wu, K. et al. An optical fibre network oracle for NP-complete problems, Light: Science & Applications. 3, e147 (2014).

Article CAS Google Scholar

Wang, X., He, C. & Wang, Z. Method for suppressing the bias drift of interferometric all-fibre optic gyroscopes, Optics Letters. 36, 1191–1193 (2011).

Article ADS Google Scholar

Bo, L. et al. An investigation of the polarization dependence of a temperature sensor based on an optical microfibre coupler, Proc. of SPIE. 8421, 84217Y (2012).

Article Google Scholar

Wang, X. & Wang, Z. Revised minimum reciprocity configuration and actualization methodology of all-fibre interferometric optic gyroscopes, Applied Optics. 50, 1856–1860 (2011).

Article ADS Google Scholar

Passos, D. J. et al. High-birefringence fibre loop mirror sensor using a WDM fused fibre coupler, Optics letters, 38, 2927–2929 (2013).

Article ADS CAS Google Scholar

Akihama, Y., Kanamori, Y. & Hane, K. Ultra-small silicon waveguide coupler switch using gap-variable mechanism. Optics Express, 19, 23658–23663 (2011).

Article ADS Google Scholar

Akihama, Y. & Hane, K. Single and multiple optical switches that use freestanding silicon nanowire waveguide couplers, Light: Science & Applications, 1, e16 (2012).

Article ADS Google Scholar

Wang, X., Yin, W. & Wu, K. A dual-band coupled-line coupler with an arbitrary coupling coefficient, IEEE Transactions on Microwave Theory and Techniques, 60, 945–951 (2012).

Article ADS Google Scholar

Tong, L. et al. Subwavelength-diameter silica wires for low-loss optical wave guiding, Nature, 426, 816–819 (2003).

Article ADS CAS Google Scholar

Eisenmann, M. & Weidel, E. Single-Mode Fused Biconical Coupler Optimized for Polarization Beamsplitting, Journal of lightwave technology, 9 853–858 (1991).

Article ADS CAS Google Scholar

Ismaeel, R. et al. All-fibre fused directional coupler for highly efficient spatial mode conversion, Optics Express, 22, 11610–11619 (2014).

Article ADS Google Scholar

Li, A. et al. Fabrication of a low-loss fused fibre spatial-mode coupler for few-mode transmission, IEEE Photonics Technology Letters, 25, 1985–1988 (2013).

Article ADS Google Scholar

Semenova, Y. et al. Spectral tuning of a microfibre coupler with a liquid crystal overlay, Proc. of SPIE, 8421, 842184 (2012).

Article Google Scholar

Eom, J. B. et al. Overcoupled bending insensitive holey optical fibre coupler, Proc. of SPIE, 8421, 842176 (2012).

Article Google Scholar

Yokota, H. et al. Fabrication of polarization-maintaining photonic crystal fibre couplers using CO2 laser irradiation technique, Proc. SPIE 7753, 7753X (2011).

Google Scholar

Gong, H. P. et al. Curvature sensor based on hollow-core photonic crystal fibre sagnac interferometer, IEEE Sensors Journal, 14, 777–780 (2014).

Article ADS Google Scholar

Eom, J. B. et al. Wavelength-division-multiplexing fibre coupler based on bending-insensitive holey optical fibre, Optics letters, 35, 2726–2728 (2010).

Article ADS Google Scholar

Han, C., Ding, H. & Lv, F. Demonstration of a refractometric sensor based on an optical micro-fibre three-beam interferometer, Scientific Reports, 4, 7504 (2014).

Article ADS CAS Google Scholar

Khorasaninejad, M. & Crozier, K. B. Silicon nanofin grating as a miniature chirality-distinguishing beam-splitter, Nature Communication. Volume: 5, 5386 (2014).

Article ADS CAS Google Scholar

Bao, Q. et al. Broadband graphene polariser, Nature Photonics. Volume: 5, 411–415 (2011).

Article ADS CAS Google Scholar

Download references

This work was supported by the State Key Laboratory of Advanced Optical Communication Systems and Networks and the Fundamental Research Funds for the Central Universities.

College of Information and Electrical Engineering, China Agricultural University, Beijing, China

Xinyue Wang

Department of Physics, Imperial College London, London, UK

Freya Thomas

Department of Electronics, State Key Laboratory of Advanced Optical Communication Systems and Networks, Peking University, Beijing, China

Ziyu Wang

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

X.W. carried out the simulations and analyses. X.W. and Z.W. conceived and designed the experiments. All authors contributed to interpretation of the data and preparation of the manuscript. X.W. and F.T. wrote the paper. Z.W. supervised the entire project.

The authors declare no competing financial interests.

This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Reprints and permissions

Wang, X., Thomas, F. & Wang, Z. Semi-reciprocal polarization maintaining fibre coupler with distinctive transmission characteristics. Sci Rep 5, 17268 (2015). https://doi.org/10.1038/srep17268

Download citation

Received: 06 September 2015

Accepted: 27 October 2015

Published: 27 November 2015

DOI: https://doi.org/10.1038/srep17268

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative